User manual ADVANCE MPP-506DA

[. . . ] Sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. HEAT The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliance (including amplifiers) that produce heat. POWER SOURCES The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. GROUNDING OR POLARIZATION Precautions should be taken so that the grounding or polarization means of an appliance is not defeated. [. . . ] CD INPUT UNBALANCED, CD INPUT BALANCED AND TUNER Press this button to select the CD RCA unbalanced (blue bottom led), press again to select CD Bal. Balanced (red bottom led) and another time to select Tuner (blue top led). AUXILIARY 1 AND AUXILIARY 2 INPUTS Press this button to select AUX1 (blue bottom led), press again to select AUX2 (blue top led). PHONO AND AES/EBU (MPP-506DA) INPUTS Press this button to select PHONO (blue bottom led), press again to select AES/EBU (blue top led). The audio signal of phono is an analog RCA type connector plus an additional ground. On the back panel, you have the possibility to adjust the cartridge type used: MM for moving magnet cartridges and MC for moving coil cartridges. Gh PC RCA, PC JACK AND lp INPUTS Press this button to select the PC RCA (red bottom led), press again to select PC JACK (blue bottom led) and another time to select ip (blue top led). Please note that two inputs connectors for PC JACK and ip are on the front panel, their input levels has been optimised (stereo minijack 3, 5mm). VOLUME BUTTON Your amplifier used a rotary type knob to control the 2 channel output sound level (left and right). Turn this volume knob clockwise to increase the ouput sound level and turn this volume knob counterclockwise to decrease the output sound level. ISOLATING SPIKES Your amplifier used spike-feet, you need to use them with non-skid cupels included. UPGRADE YOUR MPP-506 PREAMPLIFIER Your preamplifier is available in two versions, the MPP-506 (without DAC) and the MPP-506da (with DAC inside). The led DAC INSIDE lights up when your preamplifier is a MPP-506DA or a MPP-506 with DAC board inside. To obtain additionnal informations about this upgrade card, please contact your appointed dealer. wARNING ATTENTION No good Good Your product is designed to be placed on a firm and level surface. Don’t place the unit sideways, a big power exerts on the single side of the plate. These inputs are suitable for any line level source equipment such as tuners, CD players, DVD, MP3 players, etc. They should not be connected to the digital output of a CD player or any other digital device. PHONO INPUT, MM/MC SWITCH AND GROUND TERMINAL You can connect your turntable and adjust the cartridge type (MM or MC cartridge). PRE-OUT / SUBWOOFER OUT / HIGH PASS OUT / CROSSOVER FREQUENCY PRE-OUT: These connections allow you to connect L and R input from your power amplifier here. You also have the possibility to use on those connectors signal processors such as equalizers. SUBWOOFER OUT: Connect this outputs to the subwoofer power amplifier to drive your subwoofer speaker, or connect to the subwoofer speaker with built in amplifier. [. . . ] AES3 uses 110 ohm shielded twisted pair (STP) cable with XLR connectors up to a distance of 100 meters. If your source has this type of plug, then you can use it with your MPP-506DA. And use the high quality DAC converter of your preamplifier MPP-506DA in order to obtain a better sound result. USB INPUT (ONLY MPP-506DA) Note: Do not turn on the unit until all connections have been made. [. . . ]