User manual ADDONICS HDUSI5TDR

[. . . ] Once the copying process is complete the LCD will display the following results. 1 Copy HDD Copy HDD copies data directly from the source hard disk to the target hard disks. Make sure that the capacity of the target hard disk is equal or larger than the source hard disk. [. . . ] Press ENT to change the Language settings. Press ENT to begin scan. The LCD will display the following info 8. 2 Copy Size This option is used to specify the size of the source hard disk for simplifying further copying operations. Once the scan is complete, the LCD will display the corresponding results Press ENT and the LCD will display a detailed list of options as shown below 6 ReScan Bus Choose option 6 from the menu: Press ENT to re-scan hardware. The LCD will display the following info. Use the Up and Down arrow keys to choose different copy sizes. The system will offer their corresponding percentages so the user can specify the amount to copy from the source hard disk. Press ENT to confirm and save the changes. Press ENT to begin scanning IDEO0:Master/Save ~ IDE1:Master/Slave. When the scan is complete the LCD will display the following info. 8. 3 Startup Menu This option allows you to set an option other than "Setup" to be displayed as the first available option on the menu every time you start the system. 8. 8 Fast Copy This option displays Fast Copy. Fast Copy only copies data on the source drive to the target drives. Press ENT then use the Up and Down arrow keys to choose other options. By default the first menu option is Copy HDD. Press ENT and the LCD will display the following info. Use the Up and Down arrow keys to choose whether fast copy is on or off. (This function currently only supported in FAT, FAT32, NTFS, HFS, Ext2 and Ext3 partitions. ) 8. 4 Auto Compare This option automatically compares the source hard disk with the target hard disk after a copy operation is completed. 8. 9 Auto Start Drive This option is used to copy automatically once you inserted a HDD on target port. Press ENT to access option. Use the Up and Down arrow keys to choose On. Press ENT to enter the following figure. Use the Up and Down arrow keys to choose 1-5. 8. 5 Button Sound 8. 10 Auto Start Timer This option is used to set the period of time when the duplicator starts copying automatically once you insert HDD on target port. Press ENT and the LCD will display the following info. Use the Up and Down arrow keys to choose whether button sound is on or off. Press ENT to enter the following figure. Use the Up and Down arrow keys to choose 5 Sec-50 Sec. 8. 6 Device Info This option is used to display the details of all hard disks connected to the copy controller. 8. 11 Tolerance Size This option is used to set the tolerance in terms of percentage the difference in the source and target capacity. This is to ensure that when the target drive is smaller than the source drive, the duplication process will not start. Press ENT and the LCD will display each hard disk' information in order as shown below. 8. 7 System Info This option displays system information. 8. 12 BootTime Delay This option is used to set boot delay time. Appendix A LCD Messages Press ENT to enter the following figure. Use the Up and Down arrow keys to choose 0~99 sec. 5. 8. 13 Quick Compare This option is used to set the size of each comparison unit. Press ENT to enter the following figure. Use the Up and Down arrow keys to choose 1 Byte/1K/10K/100K/1MB/10MB/100 Mbytes. [. . . ] Source can't be Hard Disk!. . . . . . . . . . . . . . . . . . . . . During comparison the source cannot be hard disk. Basic Troubleshooting 9. 1 LCD If the LCD display is blank after the device is turned on, check that the power cable is properly connected and that the power supply is on. 9. 2 Error Message When the system is running a copy operation or hardware diagnostics then operation was manually terminated by pressing ESC, an error message will be shown by the LCD. This may lead to an illegal operation and cause the device to stop reminding. [. . . ]