User manual ACTIONTEC BLUETOOTH HEADSET

[. . . ] When the battery is full, the red light will turn off. Turning the Headset On/Off Turning On To turn the Headset on, press and hold the Large Button for three seconds. Two short, high-pitched tones will sound, then the blue light on the Headset will illuminate. The Headset is now turned on. Note: If the Headset's rechargeable batter is low, the red light on the Headset will flash. 5 Actiontec Wireless Bluetooth Headset User Manual Turning Off To turn the Headset off, press and hold the Large Button for three seconds. Two short, low-pitched tones will sound, then the red light will flash. [. . . ] From the menu that appears, select Pair Device. 8 Chapter 2 Using the Headset 5. On the computer, go to the Control Panel (select Start on the desktop, then Control Panel from the menu that appears) and select Sounds and Audio Devices or Multimedia. In both the "Sound Playback" and "Sound Recording" sections, click the down arrows and select Bluetooth Audio from the lists that appear. The Headset is successfully connected to the computer. 9 Actiontec Wireless Bluetooth Headset User Manual Connecting to Other Devices To connect the Headset to another type of device (a PDA, for example), the device must support Audio Gateway Profiles. Refer to the user manual of the other device to set up the Headset. 10 Troubleshooting 3 This chapter details problems that may occur when using the Headset, and possible solutions. The Red Light is flashing. When only the Red light is flashing, the Headset's rechargeable battery is running low. Plug the Headset into a wall outlet via the power adapter and recharge the battery. Full recharge takes approximately two hours. I charged the Headset's battery for 20 minutes, but it still doesn't work. The Headset's rechargeable battery must be charged for at least 40 minutes before it can be used. It is recommended, however, that the battery be charged for the full two hours. I plugged the Headset into an electrical socket, but it doesn't appear to be recharging. If the Headset hasn't been used for a long time, or the battery is nearly empty, it may take a few minutes for the Red Light to flash and indicate that it is recharging. I am getting no sound between the Headset and the device it's connected to. Check the following: · Make sure the Headset and the device have been paired. · Make sure the Headset and the device are within working range of each other. · If connecting to a cellular phone, make sure it has good signal strength. · Some cellular phones support only one Bluetooth headset at a time. Disconnection can occur if more than one Headset is being used. 11 Actiontec Wireless Bluetooth Headset User Manual My Headset connects fine, but disconnects 2 to 5 minutes after connecting. You can do this by finding the Windows Update button in the Start menu. Download any DirectX or Media Updates available. My computer says that it is connected to the Bluetooth Headset, but I'm not getting any sound through it. Make sure that you have pressed one of the buttons on the Headset to finish the connection process, and changed the Audio Device to the Bluetooth Adapter in Windows (see "Connecting to a Computer" on page 8 for more details). 12 Notices Regulatory Compliance Notices Class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] ACTIONTEC ELECTRONICS 16 Limited Warranty NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. ACTIONTEC ELECTRONICS SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR MALFUNCTION IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPT TO OPEN, REPAIR OR MODIFY THE PRODUCT, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OTHER HAZARDS, OR ACTS OF GOD. LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW, ACTIONTEC ELECTRONICS ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCT, EVEN IF ACTIONTEC ELECTRONICS OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT ACTIONTEC ELECTRONICS' OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. Disclaimer: Some countries, states or provinces do not allow the exclusion or limitation of implied warranties or the limitation of incidental or consequential damages for certain products supplied to consumers, or the limitation of liability for personal injury, so the above limitations and exclusions may be limited in their application to you. [. . . ]