User manual ACT SMART2 PRODUCT RANGE

[. . . ] ACTsmart2 Product Range Operating and Installation Instructions 18-00045 ACTsmart2 Operating and Installation Manual Rev. 1. 3 Contents ORDERING INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION NOTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 IMPORTANT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This can only be performed when the tamper is open (by removing the main unit from the mounting plate or the surface mount collar). Step 1 2 3 Keypad Entry 26 0001-1000 Press Operation Limit the number of users allowed to use ACTsmart2 - (default 1000) Maximum number allowed (leading zeroes required) End Setting User Limit User Toggle: This function will toggle the door open or closed when a vaild card or PIN is presented. To program a card or PIN with the toggle option, program as normal, but press 0 before the key. See the two examples below: Adding a Card Batch with Toggle mode: Step 1 2 3 4 5 6 Keypad Entry 10 Present Card Present Card 0 1-8, (optional)* Press Operation Add Card Batch First Card in Batch (lowest number card) Last Card in Batch (highest number card) Enable toggle mode (make sure Option 33 is set) Select each door this batch is valid for End Adding a PIN Code with Toggle mode: Step 1 2 3 4 5 Keypad Entry 12 0001-9999 0 1-8, (optional)* Press Operation Add PINs (Make sure Option 40 is set on units with keypad) 4-6 digit PIN code Enable toggle mode (make sure Option 33 is set) Select each door this PIN is valid for End 13 ACTsmart2 Operating and Installation Manual Rev. 1. 3 User Arm Function: A User with arming capability who presses the key and then presents a valid card or enters a valid PIN causes the reader to send a signal to an alarm control panel that may be used to arm/disarm the panel. This signal is sent via an auxiliary on the reader that is programmed as a "Door Armed Output". Option 42 "Arming Door" must be On before the "Door Armed Output" takes effect. If option 43 Pulse Door Armed is On, a pulsed signal is issued from this output for two seconds. The control panel in turn may send a signal to the reader to indicate that the panel is armed/disarmed. This signal is received through an auxiliary on the reader that is programmed as a "Panel Armed Input". To program a card or PIN with the arm function, program as normal, but press 9 before the key. See the two examples below: Adding a Card Batch with Arming Function: Step 1 2 3 4 5 6 Keypad Entry 10 Present Card Present Card 9 1-8, (optional)* Press Operation Add Card Batch First Card in Batch (lowest number card) Last Card in Batch (highest number card) Enable Arming mode (make sure Option 42 is set) Select each door this batch is valid for End Adding a PIN Code with Arming Function: Step 1 2 3 4 5 Keypad Entry 12 0001-9999 9 1-8, (optional)* Press Operation Add PINs (Make sure Option 40 is set on PIN and Prox Units) 4-6 digit PIN code Enable Arming mode (make sure Option 42 is set) Select each door this PIN is valid for End To summarise, the following steps are required for setting up tokens to arm and disarm alarm panels: 1. Connect up according to the Alarm Panel wiring diagram. 14 ACTsmart2 Operating and Installation Manual Rev. 1. 3 Programming ACTsmart2 Options: Step 1 2 3 4 Option 30 31 Keypad Entry 30-45 0 or 1 1-8, (optional)* Press Function Door Chime Silent Operation Operation Select Option Number 0 = Off, 1 = On Select each door this option is set for End setting options Default Off Off Operation When set, whenever the door contact is opened, the built-in buzzer makes a chime sound and the buzzer output activates for 2 seconds When set, the keypad operates silently. No audible tones (key-presses or confirm tones) are produced from the built-in buzzer When set, and when the door relay is active (following a valid code or button release), the door relay timer is truncated to 2 seconds when the door contact opens. This ensures that the door will be locked as soon as it closes, and any person following will have to enter a PIN or present a card. When set, the buzzer output / door alarm output is activated if the door contact opens when the door is locked. When set, and the door contact has been open for longer than the time programmed into the door ajar timer, the buzzer output / door alarm output is activated. Closing the door and presenting a valid card or entering a valid PIN deactivates the output. When set, (default) and when the key on the keypad is pressed, the buzzer output is activated for the duration programmed in the guest buzzer timer. When set, and when a duress PIN is entered, the door is opened normally and the Door Alarm output activated. When the duress option is set, avoid using PINs that are different by 1. This mode allows all users to have a common PIN code to use with their cards. [. . . ] Note: This deletes the Programming Card. 22 ACTsmart2 Operating and Installation Manual ACTsmart2 Standalone Installation Diagram 23 Rev. 1. 3 Access Control Technology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland. Tel: 353-1-4662570 Fax: 353-1-4520427 UK Locall: 0845 300 5204 Web: http://www. accesscontrol. ie E-mail: sales@accesscontrol. ie ACTsmart2 Operating and Installation Manual ACTsmart2 Fire Alarm Override Connections 24 ACTsmart2 Interlock Connections Rev. 1. 3 Access Control Technology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland. [. . . ]