User manual ACT ACTSMART 2 PRODUCT RANGE

[. . . ] access control TECHNOLOGY Operating & Installation Instructions for ACTSmart 2 Product Range ACTSmart2 Operating and Installation Manual Rev. 1. 1 Contents Installation Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Product Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 30 Second Programming Guide (1080) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect up according to the Alarm Panel wiring diagram. 12 ACTSmart2 Operating and Installation Manual Rev. 1. 1 Programming ACTSmart Options: Step 1 2 3 4 Option 30 31 Keypad Entry 30-43 0 or 1 1-8, (optional)* Press Function Door Chime Silent Operation Operation Select Option Number 0 = Off, 1 = On Select each door this option is set for End setting options Default Off Off Operation When set, whenever the door contact is opened, the built-in buzzer makes a chime sound and the buzzer output activates for 2 seconds When set, the keypad operates silently. No audible tones (key-presses or confirm tones) are produced from the built-in buzzer When set, and when the door relay is active (following a valid code or button release), the door relay timer is truncated to 2 seconds when the door contact opens. This ensures that the door will be locked as soon as it closes, and any person following will have to enter a PIN or present a card. When set, the buzzer output / door alarm output is activated if the door contact opens when the door is locked. When set, and the door contact has been open for longer than the time programmed into the door ajar timer, the buzzer output / door alarm output is activated. Closing the door and presenting a valid card or entering a valid PIN deactivates the output. When set, (default) and when the key on the keypad is pressed, the buzzer output is activated for the duration programmed in the guest buzzer timer. When set, and when a duress PIN is entered, the door is opened normally and the Door Alarm output activated. When the duress option is set, avoid using PINs that are different by 1. This mode allows all users to have a common PIN code to use with their cards. In this mode, users with the Arm option can switch an output to signal to an Alarm panel to arm/disarm (See I/O function code 14). When set, the Door Armed output will pulse for 2 seconds to signal arm and disarm. 13 32 Lock-saver (Anti Tailgating) Off 33 34 Toggle Door Forced Alarm Off On 35 Door Ajar Alarm On 36 Guest Button On 37 Duress Codes Off 38 39 40 41 Network Master Card and PIN Card or PIN Card and any PIN Off Off Off Off 42 43 Arming Door Pulse Door Armed Off Off ACTSmart2 Operating and Installation Manual Rev. 1. 1 Setting Programmable Input Function: Step 1 2 3 4 Keypad Entry 50 0-6 1-8 (optional)* Press Operation Set Input Function (Door Release button is default) Select I/O Function Code (see below for explanation of codes) Select each door this function is valid for End programming Input Function Setting AUX I/O 1 Function: Step 1 2 3 4 Keypad Entry 51 00-19 1-8 (optional)* Press Operation Set AUX I/O 1 Function (Door Contact is default) Select 2-digit I/O Function Code (see below) Select each door this function is valid for End programming AUX I/O 1 Setting AUX I/O 2 Function: Step 1 2 3 4 Keypad Entry 52 00-19 1-8 (optional)* Press Operation Set AUX I/O 2 Function (Door Alarm is default) Select 2-digit I/O Function Code (see below) Select each door this function is valid for End programming AUX I/O 2 I/O Function Codes: Code 0 1 Function Door Contact Fire Alarm Override Operation Input required if you wish to monitor Door Forced or Door Ajar When this input is high, the door is opened and the green LED flashes (See Fire Alarm Override Connections diagram). If this is wired into the Master Smart, then all doors on the network will open. When this input is low, then only users who enter both Card and PIN will be admitted. When this input is low, a valid Card or a valid PIN will open the door. When this input is low, any I/Os configured as Second Door Lock will open for the Door Lock Time. This normally behaves as an input and locks the door while the input is low. While the door relay is active or the Door Contact is open, it becomes an active output. This output activates while an alarm is present - A door alarm may be a door forced, door ajar, tamper or duress. [. . . ] 1. 1 Programming for SmartLock: Step 1 2 3 4 5 6 Present Programming Card Programming Card Programming Card Programming Card Programming Card Programming Card Operation Buzzer sounds intermittently and the LED flashes Input 1 = Door Contact, AUX I/O 1 = Door Alarm, AUX I/O 2 = SmartLock. See the SmartLock Connections diagram. Default ACTSmart: Step 1 2 3 4 5 Present Programming Card Programming Card Programming Card Programming Card Programming Card Present Card (Not Programming Card) Operation Buzzer sounds intermittently and the LED flashes RED to warn you are about to default the system Default ACTSmarts. Note: This deletes the Programming Card. 20 ACTSmart2 Operating and Installation Manual ACTSmart Standalone Installation Diagram 21 Rev. 1. 1 Access Control Technology, Unit 8, Tallaght Business Park, Whitestown, Dublin 24, Ireland. [. . . ]