User manual ACT ACTPRO 4000

[. . . ] Operating and Installation Instructions for the ACTpro 4000 Access Control System 18-00071 ACTpro 4000 Operating Instructions 1. 00 __________________________________________________________________________ Contents About ACTpro 4000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Time for which AUX output is active. Reporting Door Ajar Door Forced Door Open Door Closed Door left ajar events report in log. Door Closed events report in log. __________________________________________________________________________________ 17 ACTpro 4000 Operating Instructions 1. 00 __________________________________________________________________________ Push Button Read Error Mains Fault Push Button events report in log. Disable door Contact reports. Timed Actions Unlock Door Lock Door PIN Required Any Card Specify times when door is unlocked. Specify times when any card gains access. Activate OP2 Activate OP3 Activate AUX PIN Only PIN or Card Specify times when OP2 is active. Specify times for PIN or Card operation. Twin Users Two different cards required for access. Normalise Specify times when door is normalized. Assign Name Assign a name to a door. Communications Set Address Comms Speed No Hist. Disables the reporting of offline log events in slave mode. Print All Remote Doors Enables real-time logging on attached serial printer. Enable/Disable remote doors connected via DS100 modules. IO Modules Set Password Enable/Disable Input/Output modules. Set a password for remote communications. TCP/IP Settings IP Address TCP Port Num Sets the IP address of the Controller. with ACTWin pro. TCP Port Num2 Sets a second TCP port number for communications __________________________________________________________________________________ 18 ACTpro 4000 Operating Instructions 1. 00 __________________________________________________________________________ Network Mask Default Gateway MAC Address NetBIOS Name Network Speed Enable DHCP Sets the Network Mask. Enable DHCP operation. Central/Sat Central Server Central IP Addr Enable/Disable ACTpro 4000 as Central Server. Set the IP address of the Central Server. Card Setup Site Code 1 Site Code2 Card Format Enter the primary site code for the system. Enter a custom card format for the system. Diagnostics Version Reader test Voltage Check Factory Diag Last Reset Displays the current software version. Displays a code indicating the reason for the last reset. Change PIN Change the PIN used to access the Installer menu. Factory Defaults Restore the system to its factory default settings. * First it is required to select a door. Exit from menu is automatic if no keys are pressed for a period of time. __________________________________________________________________________________ 19 ACTpro 4000 Operating Instructions 1. 00 __________________________________________________________________________ System Settings The System Settings menu allows the installer to access a number of different configuration menus controlling different aspects of the setup of the controller. key toggles Operation This menu allows the installer to select or de-select a number of options relating to the default operation of the controller. · The PIN Only option allows reader-less operation using PIN codes that are directly entered on the keyboard (or on an external keypad). Almost any card with valid ISO track 2 data may be used (for example bankcards) as well as some types of wiegand card. · The Exit PINs option is requires PIN codes to be entered before the user is allowed to exit. · The User Limiting option will prevent access to tracked users when the user limit is reached. · The One-To-One option allows any card number to be captured and assigned to any of the 60, 000 users. · The Multiple option allows users to have more than one card on the system. · The TnA Terminal option allows the keypad to be used as a Time and Attendance terminal. When a card is read from door 1 or door 2, the users name is displayed and they can choose to clock-in or clock-out. Display · The Backlight option forces the keypad to be permanently illuminated, overriding the default automatic operation, which is to operate only when a user menu has been entered. [. . . ] The controller(s) will appear under the remote site name in the System View window. Double click on the telephone icon beside the remote site name in System View window. To finish the call, click the disconnect button on ACTWin pro 47 Alarm Panel Wiring Diagram Common the 0V line of each Controller Alarm Panel Disarmed While the AUX input is active (connected to 0V), the door is locked. Note: 0V line of ACT Controller system is connected to the 0V of the alarm panel. OUTPUTS 1 INPUTS PUSH BUTTON DOOR I/O DOOR CONTACT AUX INPUT N/C C N/ON/C C N/O AUX RLY 0V OP2 OP3 OP3 OP2 0V AUX DOOR CONTACT PUSH BUTTON 5A 250VAC 5A 30VDC RELAY Input 0V COMM N/O 5A 250VAC 5A 30VDC 1A 250VAC 1A 30VDC 5A 250VAC 5A 30VDC TAMPER MAINS +12V 0V 12345678 On WP 2 Address Connect AUX Relay output from controller to arm input on panel. [. . . ]