User manual ACEC HTX290

[. . . ] Special information for gas cookers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Proper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Correct installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exhaust-air mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Circulating-air mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] NOTE: When making your evaluation, always consider the entire ventilation system in the home. Include the advice of a competent heating engineer when making your evaluation. If the extractor hood is used in circulating air mode only, it can be operated without any restrictions. 6 Safety instructions Proper use Clean the extractor hood thoroughly before using for the first time. Before cleaning and servicing the extractor hood, isolate it from the power supply by pulling out the mains plug or switching off the fuse. Even some time after the appliance has been switched off, there is still a risk of burns!Before changing bulbs, isolate the extractor hood from the power supply and leave the bulbs to cool down!Do not place any objects on the extractor hood. Correct installation Check the manufacturer's specifications for the cooker to determine whether an extractor hood can be operated over it. If the manufacturer of the cooker has not specified any significant safety distances, the following minimum distances apply ­ 550 mm between electric hob and the lower edge of the extractor hood ­ 650 mm between gas hob (upper edge of pan support) and the lower edge of the extractor hood, (see fig. The width of the extractor hood must correspond to the width of the cooking area. The extractor hood must not be installed over a solid fuel heating appliance which may be a fire risk (e. g. flying sparks) unless the heating appliance has a closed, nondetachable cover and the country-specific regulations are observed. Reinsert the grease filters (see Removing and installing the metal-mesh grease filters). Changing the activated carbon filter Under normal operation (daily 1 to 2 hours) the activated carbon filters must be replaced approximately 2x year. The activated carbon filter is available from specialist outlets, customer service or the Online Shop (see Optional accessories). They can be disposed of in the household refuse. (for appliances with edge extraction) 2. Reinsert the cleaned grease filters. 11 Changing the bulbs Before changing the bulbs, always follow the instructions and warnings in the chapter entitled "Safety instructions"!The description of changing the bulbs applies to several appliance models. NOTE: Observe the warranty regulations in the enclosed service booklet. Changing the filament bulbs 1. Push the bulb cover towards the middle of the appliance. 2 1 Changing the halogen bulbs Halogen bulbs become very hot during operation. Even some time after the appliance has been switched off, there is still a risk of burns!Before changing the halogen bulbs, ensure that they have cooled down fully. Replace the defective bulb with a new one of the same type and equivalent power (see rating plate). Replace the defective bulb with a new one of the same type and equivalent power (see rating plate). [. . . ] Attach the earthed socket as directly as possible behind the flue duct. ­ If the earthed socket is no longer accessible following installation of the extractor hood, a disconnector must be fitted as for a permanent connection. If a permanent connection is required A disconnector must be provided on the installation side. Switches with a contact opening of more than 3 mm and all-pole disconnection are regarded as disconnectors. This includes LS switches, fuses and contactors. Electrical specifications WARNING: THIS APPLIANCE MUST BE EARTHED IMPORTANT: Fitting a Different Plug: The wires in the mains lead are coloured in accordance with the following code: Green and Yellow ­ Earth Blue ­ Neutral Brown ­ Live If you fit your own plug, the colours of these wires may not correspond with the identifying marks on the plug terminals. [. . . ]