User manual ABIT WI-2PA

[. . . ] WI-2Pa Dual Socket 604 Workstation Board User's Manual 4200-0349-22 Rev. 1. 00 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. [. . . ] User's Manual 3-12 Chapter 3 USB 2. 0 Controller This item allows you to select the USB ports to be USB 2. 0 ([Enabled]) or USB 1. 1 ([Disabled]) specification. USB Keyboard Support This item allows you to select [BIOS] for using USB keyboard in DOS environment, or [OS] in OS environment. USB Mouse Support This item allows you to select [BIOS] for using USB mouse in DOS environment, or [OS] in OS environment. AC97 Audio When set to [Enabled], the onboard audio codec will be detected and supported. IF you want to use audio adapter other than the one onboard, set this item to [Disabled] Onboard LAN Controller This item enables or disables the onboard LAN controller. Onboard LAN Boot ROM When set to [Enabled], this item allows the system to boot from network by the onboard LAN controller boot ROM. Init Display First Two options are available: PCI Slot and AGP. When you install an additional display card, you can choose either a PCI display card or an AGP display card to activate the display boot-up screen. POWER ON Function This item allows you to select which way you want your system to power on. Seven items are available: Password Hot Key Mouse Left Mouse Right Any Key BUTTON ONLY Keyboard 98. NOTE: The mouse wake up function can only be used with the PS/2 mouse, not with a mouse that uses the COM port and USB connection. Mouse Left (Mouse Right) means you need to double click the mouse left (right) button, for the computer to power on. Some PS/2 mice cannot wake up the system because of compatibility problems. Also, if the specs of your keyboard are too old, it may fail to power on. WI-2Pa BIOS Setup 3-13 KB Power ON Password This option allows you to set a password required in order to Power ON your computer. Should you forget your password, you will have to open your computer case, clear the CMOS and reset all parameters again in order to be able to utilize this function. Hot Key Power ON There are twelve options are available, Ctrl-F1 to Ctrl-F12. You can select this item and using the <Ctrl> plus the one of each function key (F1 to F12) to power on the computer. Onboard FDD Controller This item enables or disables the onboard FDD controller. Onboard Serial Port 1 This item specifies the I/O address and IRQ of Serial Port 1. Onboard Serial Port 2 This item specifies the I/O address and IRQ of Serial Port 2. Onboard IR Function This item enables or disables the onboard IR function. The options are: IrDA (HPSIR) mode ASK IR (Amplitude Shift Keyed IR) mode Disabled. RxD , TxD Active Four options are available: Hi, Hi Hi, Lo Lo, Hi Lo, Lo. Set IR transmission/reception polarity as High or Low. IR Transmission Delay Two options are available: Enabled and Disabled. Set IR transmission delays 4 character-time (40 bit-time) when SIR is changed from RX mode to TX mode. UR2 Duplex Mode Two options are available: Full and Half. Refer to your IR KIT user's guide to find out which setting is correct. User's Manual 3-14 Chapter 3 Use IR Pins Two options are available: RxD2, TxD2 and IR-Rx2Tx2. If you choose RxD2, TxD2, your workstation board must support a COM port IR KIT connection. Otherwise, you can only choose the IR-Rx2Tx2 to use the IR header on your workstation board to connect your IR KIT. Please use the default setting. Onboard Parallel Port This item sets the address of the onboard parallel port. Parallel Port Mode This item sets the operation mode of the parallel port. [SPP] (Standard Parallel Port) allows bi-directional parallel port operation at normal speed; [ECP] (Extended Capabilities Port) allows bi-directional parallel port operation at a speed faster than the normal mode's data transfer rate; [EPP] (Enhanced Parallel Port) allows bi-directional parallel port operation at maximum speed. EPP Mode Select This item selects the EPP mode. ECP Mode Use DMA Two options are available: 1 3. When the mode selected for the parallel port mode is ECP, the DMA channel selected can be Channel 1 or Channel 3. PWRON After PWR-Fail This item sets the system action after a power failure. Game Port Address This item sets the address of the onboard game port connector. Midi Port Address This item sets the address of the onboard midi port connector. Midi Port IRQ This item sets the IRQ of the onboard midi port connector. If you choose disable the Midi Port Address, then this field is not available. WI-2Pa BIOS Setup NOTE: If you bought an audio adapter and wanted to replace the use of onboard audio solution, you have to disable three items in BIOS. These three items are: AC 97 Audio: set to Disabled Game Port Address: set to Disabled Midi Port Address: set to Disabled 3-15 User's Manual 3-16 Chapter 3 3. 2. 4. Power Management Setup This menu allows you to set up the power management in order to reduce power consumption. ACPI Suspend Type: Two options are available: S1(POS) and S3(STR). [. . . ] After all, your reseller regards you as an important customer who may purchase more products and who can urge your friends to buy from him or her as well. They should know best what your system configuration is and your problem. If you feel that you need to contact ABIT directly you can send email to the ABIT technical support department. First, please contact the support team for the branch office closest to you. [. . . ]