User manual ABIT SI-2NS441

[. . . ] SI-2Ns44X Series Dual Xeon Server Board Socket 604 User's Manual Rev. 1. 00 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. [. . . ] When the value of this option is set to [Disabled], the printer port becomes unavailable. [378/IRQ7]: This option allows the parallel port to use [378/IRQ7] as its I/O port address. The majority of parallel ports on computer systems use IRQ7 and I/O Port 378H as the standard setting. [278/IRQ5]: This option allows the parallel port to use [278/IRQ5] as its I/O port address. [3BC/IRQ7]: This option allows the parallel port to use [3BC/IRQ7] as its I/O port address. [SPP]: (Standard Parallel Port) Allows bi-directional parallel port operation at normal speed. [EPP]: (Enhanced Parallel Port) Allows bi-directional parallel port operation at maximum speed. [ECP]: (Extended Capabilities Port) Allows bi-directional parallel port operation at a speed faster than the normal mode's data transfer rate. ECP Mode Use DMA: This item selects the DMA channel of the parallel port. SI-2Ns44X Series BIOS Setup 3-15 Onboard PCI Device: Click <Enter> key to enter its submenu: Graphic Controller This item enables or disables the onboard graphic controller. CN1120 Controller This item enables or disables the onboard security processor. Network-1/2 Controller This item enables or disables the onboard LAN1/LAN2 Controller. Invoke Boot Agent This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. Network-3/4 Controller This item enables or disables the onboard LAN3/LAN4 Controller. Invoke Boot Agent This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. User's Manual 3-16 Chapter 3 Network-5/6 Controller This item enables or disables the onboard LAN5/LAN6 Controller. Invoke Boot Agent This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. Network-7/8 Controller This item enables or disables the onboard LAN7/LAN8 Controller. Invoke Boot Agent This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. 3. 2. 4. Power Management Setup Power Button Function This item selects the method of powering off your system: [Delay 4 Sec. ]: Pushing the power button for more than 4 seconds will power off the system. This will prevent the system from powering off in case you accidentally hit or pushed the power button. SI-2Ns44X Series BIOS Setup 3-17 [Instant-Off]: Pressing and then releasing the power button at once will immediately power off the system. CPU THRM-Throttling This item controls the CPU speed by cutting down its regular power to a percentage during the STR (Suspend To RAM) state. Wake-Up by PME# of PCI When set to [Enabled], access to the onboard LAN or a PCI card such as a modem or LAN card will cause the system to wake up. WakeUp by Alarm When set to [Enabled], you can set the date and time you would like the Soft-Off PC to power-on in the "Date (of Month) Alarm" and "Time (hh:mm:ss) Alarm" items. However, if the system is being accessed by incoming calls or the network (Resume On Ring/LAN) prior to the date and time set in these items, the system will give priority to the incoming calls or network instead. [. . . ] They should know best what your system configuration is and your problem. If you feel that you need to contact ABIT directly you can send email to the ABIT technical support department. First, please contact the support team for the branch office closest to you. They will be more familiar with local conditions and problems and will have better insight as to which resellers offer what products and services. [. . . ]