User manual ABIT SI-1NS42-60

[. . . ] SI-1Ns42 SI-1Ns60 Intel Pentium 4 Server Board Socket 478 User's Manual Rev. 1. 00 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. [. . . ] Onboard LAN2 Controller: This option enables or disables the LAN2 controller. LAN Boot ROM: This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. Onboard LAN3 Controller: This option enables or disables the LAN3 controller. LAN Boot ROM: This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. Onboard LAN4 Controller: This option enables or disables the LAN4 controller. LAN Boot ROM: This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. Onboard LAN5 Controller: This option enables or disables the LAN5 controller. LAN Boot ROM: This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. User's Manual 3-12 Onboard LAN6 Controller: This option enables or disables the LAN6 controller. LAN Boot ROM: Chapter 3 This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. SuperIO Device: Click <Enter> key to enter its submenu: Onboard Serial Port 1: This item determines which I/O addresses the onboard Serial Port 1 controller will access. [Auto]: The system automatically select an I/O address for the onboard Serial Port 1. [3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3]: Allows you to manually select an I/O address for the onboard Serial Port 1. Onboard Serial Port 2: This item determines which I/O addresses the onboard Serial Port 2 controller will access. [Auto]: The system automatically select an I/O address for the onboard Serial Port 2. SI-1Ns42/SI-1Ns60 BIOS Setup 3-13 [3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3]: Allows you to manually select an I/O address for the onboard Serial Port 2. [Disabled]: Disables the onboard Serial Port 2. Back to Integrated Peripherals Setup Menu: Init Display First: This item selects to initialize Onboard VGA or PCI Slot first when the system boots. [Onboard VGA]: When the system boots, it will first initialize the onboard VGA. [PCI Slot]: When the system boots, it will first initialize PCI Slot. User's Manual 3-14 Chapter 3 3. 5. Power Management Setup ACPI Suspend Type: This item selects the type of Suspend mode. Resume by USB From S3: When set to [Enabled], this item allows you to use a USB device to wake up a system that is in the S3 (STR - Suspend To RAM) state. This item can be configured only if the item "ACPI Suspend Type" is set to [S3(STR)]. Power Button Function This item selects the method of powering off your system: [Delay 4 Sec. ]: Pushing the power button for more than 4 seconds will power off the system. [. . . ] They should know best what your system configuration is and your problem. If you feel that you need to contact ABIT directly you can send email to the ABIT technical support department. First, please contact the support team for the branch office closest to you. They will be more familiar with local conditions and problems and will have better insight as to which resellers offer what products and services. [. . . ]