User manual ABIT NF7-S2G VERSION 2

[. . . ] NF7 Series (NF7/NF7-M/NF7-S/NF7-S2/NF7-S2G) Socket 462 System Board User's Manual 4200-0316-10 Rev. 1. 01 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. [. . . ] USB Keyboard Support via: This item allows you to select [BIOS] for using USB keyboard in DOS environment, or [OS] in OS environment. USB Mouse Support via: This item allows you to select [BIOS] for using USB mouse in DOS environment, or [OS] in OS environment. USB2. 0 Device Compatible: This item enables or disables the compatibility with USB2. 0 devices. User's Manual 3-18 Chapter 3 Audio Controller: This option enables or disables the audio controller. LAN Boot ROM: This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. IEEE1394 Controller (For NF7-S Only): This option enables or disables the IEEE 1394 controller. Back to Integrated Peripherals Setup Menu: Onboard PCI Device (For NF7-S Only): Click <Enter> key to enter its submenu: Serial ATA Controller: This option enables or disables the onboard Silicon Image SIL3112A SATA controller. SATA RAID ROM: This item allows you to use the boot ROM of onboard Serial ATA RAID to boot-up system. Back to Integrated Peripherals Setup Menu: Init Display First: This item selects to initialize AGP or PCI Slot first when the system boots. [AGP]: When the system boots, it will first initialize AGP. NF7 Series BIOS Setup 3-19 EXT-P2P's Discard Time: This item allows you to set EXT-P2P's discard time. Onboard FDD Controller: Two options are available: Enabled and Disabled. Onboard Serial Port 1: This is used to specify the I/O address and IRQ of Serial Port 1. Six options are available: Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 AUTO. Onboard Serial Port 2: This is used to specify the I/O address and IRQ of Serial Port 2. Six options are available: Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 AUTO. If you choose Disabled, the following items will not be available to set. Onboard IR Function: Three options are available: IrDA (HPSIR) default setting is Disabled. The When you select the item IrDA or ASKIR, the following items will be available to set. RxD , TxD Active: Four options are available: Hi, Hi Hi, Lo Lo, Hi transmission/reception polarity as High or Low. IR Transmission Delay: Two options are available: Enabled and Disabled. Set IR transmission delays 4 character-time (40 bit-time) when SIR is changed from RX mode to TX mode. Half-duplex mode permits transmission in only one direction at a time. If you choose RxD2, TxD2, your motherboard must support a COM port IR KIT connection. Otherwise, you can only choose the IR-Header to use the IR header on your motherboard to connect your IR KIT. [. . . ] After all, your reseller regards you as an important customer who may purchase more products and who can urge your friends to buy from him or her as well. They should know best what your system configuration is and your problem. If you feel that you need to contact ABIT directly you can send email to the ABIT technical support department. First, please contact the support team for the branch office closest to you. [. . . ]