User manual ABIT NF-M2SV

[. . . ] NF-M2P NF-M2S NF-M2SV Motherboard AMD Socket AM2 Installation Guide Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. [. . . ] Attach the SATA power cable to the SATA device and connect the other end from the power supply. The motherboard in this photo is served for DEMO only, and may not be the same type or model as the one described in this manual. 1. 8. 3 Additional USB 2. 0 Port Headers Each header supports 2x additional USB 2. 0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis. NF-M2P: NF-M2S/NF-M2SV: NF-M2P/NF-M2S/NF-M2SV 13 NF-M2S/NF-M2SV: 1. 8. 4 Internal Audio Connectors This connector connects to the audio output of internal CD-ROM drive or add-on card. Pin 1 3 5 7 Pin Assignment VCC Data0 Data0 + Ground Pin 2 4 6 8 10 Pin Assignment VCC Data1 Data1 + Ground NC Make sure the connecting cable bears the same pin assignment. 14 NF-M2P/NF-M2S/NF-M2SV 1. 8. 5 Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. 1. 8. 6 PCI and PCI Express X16, X1 Slots Install PCI Express X16 graphics card into slot "PCIEX16". Install PCI cards into slots "PCI1" and/or "PCI2". Pin 1 2 3 4 5 6 7 8 9 10 Signal Name AUD_MIC AUD_GND AUD_MIC_BIAS AUD_VCC Filtered AUD_F_R AUD_RET_R REVD Key AUD_F_L AUD_RET_L Function Front Panel Microphone input signal Ground used by Analog Audio Circuits Microphone Power +5V used by Analog Audio Circuits Right Channel audio signal to Front Panel Right Channel Audio signal to Return from Front Panel Reserved No Pin Left Channel Audio signal to Front Panel Left Channel Audio signal to Return from Front Panel NF-M2P/NF-M2S/NF-M2SV 15 1. 9 Connecting Rear Panel I/O Devices The rear I/O part of this motherboard provides the following I/O ports: NF-M2P/NF-M2S: · · LAN1: Connects to Local Area Network. (Rear Left / Rear Right): Connects to the rear left and rear right channel. (Surround Left / Surround Right): Connects to the surround left and surround right channel. AUDIO1: (For model NF-M2SV) Line-In: Connects to the line out from external audio sources. Mic-In: Connects to the plug from external microphone. · NF-M2SV: · · · · · · Mouse: Connects to PS/2 mouse. LPT1: Connects to printer or other devices that support this communication protocol. COM1: Connects to external modem, mouse or other devices that support this communication protocol. USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard, hub, digital camera, joystick etc. BIOS Setup This motherboard provides a programmable EEPROM so that you can update the BIOS utility. The BIOS (Basic Input/Output System) is a program that deals with the basic level of communication between processor and peripherals. Use the BIOS Setup program only when installing motherboard, reconfiguring system, or prompted to "Run Setup". After powering up the system, the BIOS message appears on the screen, the memory count begins, and then the following message appears on the screen: Phoenix ­ AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving PRESS DEL TO ENTER SETUP If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt> + <Del> keys, or by pressing the Reset button on computer chassis. Only when these two methods fail should you restart the system by powering it off and then back on. After pressing <Del> key, the main menu screen appears. Esc: Quit F10: Save & Exit Setup : Select Item Time, Date, Hard Disk Type. . . In order to increase system stability and performance, our engineering staff is constantly improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual are for your reference only, and may not completely match with what you see on your screen. Do not change the BIOS parameters unless you fully understand its function. NF-M2P/NF-M2S/NF-M2SV 17 3. Driver & Utility The "Driver & Utility CD" that came packed with this motherboard contains drivers, utilities and software applications required for its basic and advanced features. Place the "Driver & Utility CD" into the CD-ROM drive in your system. If not, browse the root directory of the CD-ROM via the File Manager, and double click the "AUTORUN" file. · · · · · [Drivers]: Click to enter the driver installation menu. [abit Utility]: Click to enter the installation menu of utilities exclusively developed by abit. [. . . ] Example: 512M* 4PCS Memory configuration: Type in the memory configuration in BIOS setting. Example: Memory Timing: 2. 5-3-3-7 @533MHz Graphics information: Note Graphics card's brand, model and driver version Graphics card: Type in the brand and model name of your graphics card. Example: ATI RADEON X850 XT PE Graphics driver version: Type in the driver version of your graphics card Example: Catalyst 5. 12V Power supply maker: Type in the brand and model name of your power supply unit. Power supply wattage: Type in the power wattage of your power supply unit. [. . . ]