User manual ABIT NF-M2-NVIEW

[. . . ] Introduction Hardware Setup BIOS Setup Driver & Utility CD NF-M2 nView NVIDIA 6150/NF430 2GHz HT Dual DDR2 800 Motherboard AMD Socket AM2 NV nView GeForce 6150 Graphics DVI/VGA Out NV GbE 4x SATA 3Gb/s Appendix User's Manual 7. 1 HD Audio NF-M2 nView User's Manual English, 1st Edition August, 2006 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. [. . . ] Landing Zone This item displays the number of cylinders specified as the landing zone for the read/write heads. Sector This item configures the number of sectors per track. Back to Standard CMOS Features Setup Menu: Drive A & Drive B This item sets the type of floppy drives (usually only Drive A) installed. Floppy 3 Mode Support This item allows you to use "3 Mode Floppy Drive" in Japanese computer system by selecting drive A, B, or both. Leave this item at its default [Disabled] setting if you are not using this Japanese standard floppy drive. Halt On This item determines whether the system stops if an error is detected during system boot-up. [All Errors]: The system-boot will stop whenever the BIOS detect a non-fatal error. [All, But Keyboard]: The system-boot will stop for all errors except a keyboard error. [All, But Diskette]: The system-boot will stop for all errors except a diskette error. [All, But Disk/Key]: The system-boot will stop for all errors except a diskette or keyboard error. Base Memory This item displays the amount of base memory installed in the system. The value of the base memory is typically 640K for system with 640K or more memory size installed on the motherboard. Extended Memory This item displays the amount of extended memory detected during system boot-up. Total Memory This item displays the total memory available in the system. 3-6 NF-M2 nView 3. 3 Advanced BIOS Features Phoenix ­ Award BIOS CMOS Setup Utility Advanced BIOS Features Quick Power on Self Test Enabled Hard Disk Boot Priority Press Enter First Boot Device Floppy Second Boot Device Hard Disk Third Boot Device CDROM Boot Other Device Enabled Boot Up Floppy Seek Disabled Boot Up NumLock Status On Security Option Setup MPS Version Ctrl For OS 1. 4 Delay For HDD (Secs) 0 Full Screen Logo Show Enabled Item Help :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults BIOS Setup Quick Power On Self Test When set to [Enabled], this item speeds up the Power On Self Test (POST) after powering on the system. Hard Disk Boot Priority This item selects the hard disks booting priority. By pressing <Enter> key, you can enter its submenu where the hard disks detected can be selected for the booting sequence to boot up system. This item functions only when there is the option of [Hard Disk] in any one of the First/Second/Third Boot Device items. First Boot Device / Second Boot Device / Third Boot Device / Boot Other Device Select the drive to boot first, second and third in the [First Boot Device], [Second Boot Device], and [Third Boot Device] items respectively. The BIOS will boot the operating system according to the sequence of the drive selected. Set [Boot Other Device] to [Enabled] if you wish to boot from another device other than these three items. Boot Up Floppy Seek When the computer boots up, the BIOS detects if the system has a FDD or not. When this item is set to Enabled, if the BIOS detects no floppy drive, it will display a floppy disk drive error message. Boot Up NumLock Status This item determines the default state of the numeric keypad at system booting up. NF-M2 nView 3-7 [On]: The numeric keypad functions as number keys. [. . . ] (Illustrate the over-clocking status if you had done so. ) Example: Intel 650 3. 4GHz (OC FSB=220MHz) Memory brand: Type in the brand and model name of your memory module. Example: Memory brand: Kingston (KVR533D2N4/1G) Memory size: Type in the size of your memory module. Example: 512M* 4PCS Memory configuration: Type in the memory configuration in BIOS setting. Example: Memory Timing: 2. 5-3-3-7 @533MHz Graphics information: Note Graphics card's brand, model and driver version Graphics card: Type in the brand and model name of your graphics card. [. . . ]