User manual ABIT LG-95Z

[. . . ] LG-95Z LG-95C Motherboard Intel Socket 775 Installation Guide V2. 0 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. [. . . ] Attach either end of the signal cable to the SATA connector on motherboard. Attach the SATA power cable to the SATA device and connect the other end from the power supply. Connect the single end (blue connector) at the longer length of ribbon cable to the IDE port of this board, the other two ends (gray and black connector) at the shorter length of the ribbon cable to the connectors of your hard drives. Make sure to configure the "Master" and "Slave" relation before connecting two drives by one single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector. The motherboard in this photo is served for DEMO only, and may not be the same type or model as the one described in this manual. LG-95Z V2. 0/LG-95C 9 1. 7. 3 Additional USB 2. 0 Port Headers Each header supports 2x additional USB 2. 0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis. 1. 7. 4 Internal Audio Connectors This connector connects to the audio output of internal CD-ROM drive or add-on card. Pin 1 3 5 7 Pin Assignment VCC Data0 Data0 + Ground Pin 2 4 6 8 10 Pin Assignment VCC Data1 Data1 + Ground NC Make sure the connecting cable bears the same pin assignment. 10 LG-95Z V2. 0/LG-95C 1. 7. 5 Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. 1. 7. 6 PCI and PCI Express X16, X1 Slots Install PCI Express X16 graphics card into slot "PCIEX16" or "PCIEX4". Install PCI cards into slots "PCI1" and/or "PCI2". Slot PCIEX16 supports up to X16 bandwidth but is available for model LG-95C only. Pin 1 2 3 4 5 6 7 8 9 10 Signal Name AUD_MIC AUD_GND AUD_MIC_BIAS AUD_VCC Filtered AUD_F_R AUD_RET_R REVD Key AUD_F_L AUD_RET_L Function Front Panel Microphone input signal Ground used by Analog Audio Circuits Microphone Power +5V used by Analog Audio Circuits Right Channel audio signal to Front Panel Right Channel Audio signal to Return from Front Panel Reserved No Pin Left Channel Audio signal to Front Panel Left Channel Audio signal to Return from Front Panel LG-95Z V2. 0/LG-95C 11 1. 8 Connecting Rear Panel I/O Devices The rear I/O part of this motherboard provides the following I/O ports: · · · · · · Mouse: Connects to PS/2 mouse. LPT1: Connects to printer or other devices that support this communication protocol. COM1: Connects to external modem, mouse or other devices that support this communication protocol. USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard, hub, digital camera, joystick etc. (Rear Left / Rear Right): Connects to the rear left and rear right channel. (Surround Left / Surround Right): Connects to the surround left and surround right channel. BIOS Setup This motherboard provides a programmable EEPROM so that you can update the BIOS utility. The BIOS (Basic Input/Output System) is a program that deals with the basic level of communication between processor and peripherals. Use the BIOS Setup program only when installing motherboard, reconfiguring system, or prompted to "Run Setup". After powering up the system, the BIOS message appears on the screen, the memory count begins, and then the following message appears on the screen: CMOS Setup Utility ­ Copyright (C) 1985-2005, American Megatrends, Inc. Standard CMOS Setup Advanced Setup Advanced Chipset Setup Integrated Peripherals Power Management Setup PCI/PnP Configuration PC Health Status Frequency/Voltage Control Load Optimal Defaults Supervisor Password User Password Save & Exit Setup Exit Without Saving PRESS DEL TO ENTER SETUP If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt> + <Del> keys, or by pressing the Reset button on computer chassis. Only when these two methods fail should you restart the system by powering it off and then back on. After pressing <Del> key, the main menu screen appears. :Move Enter:Select +/-/:Value F10:Save and Exit F1:General Help F9:Optimized Defaults Esc:Exit v02. 58 (C)Copyright 1985-2005, American Megatrends, Inc. In order to increase system stability and performance, our engineering staff is constantly improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual are for your reference only, and may not completely match with what you see on your screen. function. Do not change the BIOS parameters unless you fully understand its LG-95Z V2. 0/LG-95C 13 3. Driver & Utility The "Driver & Utility CD" that came packed with this motherboard contains drivers, utilities and software applications required for its basic and advanced features. Place the "Driver & Utility CD" into the CD-ROM drive in your system. If not, browse the root directory of the CD-ROM via the File Manager, and double click the "AUTORUN" file. · · · · · [Drivers]: Click to enter the driver installation menu. [. . . ] Example: 512M* 4PCS Memory configuration: Type in the memory configuration in BIOS setting. Example: Memory Timing: 2. 5-3-3-7 @533MHz Graphics information: Note Graphics card's brand, model and driver version Graphics card: Type in the brand and model name of your graphics card. Example: ATI RADEON X850 XT PE Graphics driver version: Type in the driver version of your graphics card Example: Catalyst 5. 12V Power supply maker: Type in the brand and model name of your power supply unit. Power supply wattage: Type in the power wattage of your power supply unit. [. . . ]