User manual ABIT LG-95

[. . . ] Hardware Setup BIOS Setup Driver & Utility Multilingual QIG LG-95 LG-95Z Motherboard Socket 775 Intel Core 2 Duo* / Pentium Dual-Core / Pentium D / Pentium 4 / Celeron D Intel 945G (945GZ)* / ICH7 FSB1066 (800)* DDR2 667 (533)* Integrated Intel GMA 950 Gigabit LAN (10/100)* Appendix 4x SATA 3. 0Gb/s 7. 1 Channel HD Audio Vista Premium HW Ready * See the "Specifications" of each model for details. LG-95/LG-95Z User's Manual English + Multilingual QIG 1st Edition, December 2006 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. [. . . ] Power off the computer and unplug the AC power cord before installing or removing memory modules. Hold two edges of the DIMM module carefully, keep away from touching its connectors. Firmly press the module into the slots until the ejector tabs at both sides of the slot automatically snap into the mounting notch. Do not force the DIMM module in with extra force as the DIMM module only fits in one direction. To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and then pull out the DIMM module. Static electricity can damage the electronic components of the computer or optional boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a grounded metal object briefly. 2. LG-95/LG-95Z 1-13 1. 8 Connecting Peripheral Devices 1. 8. 1 Floppy and IDE Disk Drive Connectors The FDC1 connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable. Connect the single end at the longer length of ribbon cable to the FDC1 on the board, the two connectors on the other end to the floppy disk drives connector. The red line on the ribbon cable must be aligned with pin-1 on both the FDC1 port and the floppy connector. Each of the IDE port connects up to two IDE drives at Ultra ATA/100 mode by one 40-pin, 80-conductor, and 3-connector Ultra ATA/66 ribbon cables. Connect the single end (blue connector) at the longer length of ribbon cable to the IDE port of this board, the other two ends (gray and black connector) at the shorter length of the ribbon cable to the connectors of your hard drives. Make sure to configure the "Master" and "Slave" relation before connecting two drives by one single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector. 1-14 LG-95/LG-95Z Hardware Setup 1. 8. 2 Serial ATA Connectors Each SATA connector serves as one single channel to connect one SATA device by SATA cable. To connect SATA device: 1. Attach either end of the signal cable to the SATA connector on motherboard. Attach the SATA power cable to the SATA device and connect the other end from the power supply. The motherboard in this illustration is served for DEMO only, may not be the same type or model as the one described in this user's manual. 2. LG-95/LG-95Z 1-15 1. 8. 3 Additional USB 2. 0 Port Headers Each header supports 2x additional USB 2. 0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis. Pin 1 3 5 7 Pin Assignment VCC Data0 Data0 + Ground Pin 2 4 6 8 10 Pin Assignment VCC Data1 Data1 + Ground NC Make sure the connecting cable bears the same pin assignment. 1. 8. 4 Internal Audio Connectors This connector connects to the audio output of internal CD-ROM drive or add-on card. 1-16 LG-95/LG-95Z Hardware Setup 1. 8. 5 Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. Pin 1 2 3 4 5 6 7 8 9 10 Signal Name PORT1 L GND PORT1 R PRESENCE# PORT2 R SENSE1_RETURN SENSE_SEND Key PORT2 L SENSE2_RETURN LG-95/LG-95Z 1-17 1. 8. 6 PCI and PCI Express X16, X1 Slots Install PCI Express X16 graphics card into slot "PCIEX16". (For LG-95 only) Install PCI Express X1 card into slot "PCIEX1". Install PCI cards into slots "PCI1" and/or "PCI2". 1-18 LG-95/LG-95Z Hardware Setup 1. 9 Connecting Rear Panel I/O Devices The rear I/O part of this motherboard provides the following I/O ports: · · · · · · · · Mouse: Connects to PS/2 mouse. LPT1: Connects to printer or other devices that support this communication protocol. COM1: Connects to external modem, mouse or other devices that support this communication protocol. USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard, hub, digital camera, joystick etc. (Center / Subwoofer): Connects to the center and subwoofer channel in the 7. 1 channel audio system. (Rear Left / Rear Right): Connects to the rear left and rear right channel in the 7. 1 channel audio system. [. . . ] Example: AA8XE REV: 1. 00 BIOS Version: Type in the BIOS version of your motherboard. (You can find it on the screen during the POST sequence. ) CPU: Type in the brand name and the speed (MHz) of your CPU. (Illustrate the over-clocking status if you had done so. ) Example: Intel 650 3. 4GHz (OC FSB=220MHz) Memory brand: Type in the brand and model name of your memory module. Example: Memory brand: Kingston (KVR533D2N4/1G) Memory size: Type in the size of your memory module. [. . . ]