User manual ABIT KW7

[. . . ] KW7 Series (KW7, KW7-G) AMD Athlon XP System Board Socket 462 User's Manual 4200-0416-02 Rev. 1. 01 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. [. . . ] The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2. 2. Back to Advanced Chipset Features Setup Menu: Memory Hole At 15-16M: When set to [Enabled], the memory address space at 15M-16M will be reserved for ISA expansion cards that specifically requires this setting. Top performance: This item enables the DRAM performance if there are no compatible issues occurred. User's Manual 3-16 Chapter 3 3-5. Integrated Peripherals Phoenix ­ AwardBIOS CMOS Setup Utility Integrated Peripherals OnChip IDE Device [Press Enter] OnChip PCI Device [Press Enter] SuperIO Device [Press Enter] Init Display First [PCI Slot] Onboard Lan Controller [Disabled] Onboard IEEE1394 Controller [Disabled] PWRON After PWR-Fail [Off] Item Help :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults OnChip IDE Device: Click <Enter> key to enter its submenu: Phoenix ­ AwardBIOS CMOS Setup Utility OnChip IDE Device IDE Prefetch Mode [Enabled] - SATA Mode [RAID] OnChip IDE-1 Controller [Enabled] OnChip IDE-2 Controller [Enabled Item Help :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults KW7 Series BIOS Setup 3-17 IDE Prefetch Mode: Two options are available: Disabled or Enabled. The onboard IDE drive interfaces supports IDE prefetching for faster drive accesses. If you install a primary and/or secondary add-in IDE interface, set this field to Disabled if the interface does not support prefetching. OnChip IDE-1 Controller/OnChip IDE-2 Controller: This item allows you to enable or disable the primary and secondary IDE controller. Select [Disabled] if you want to add a different hard drive controller. OnChip PCI Device: Click <Enter> key to enter its submenu: Phoenix ­ AwardBIOS CMOS Setup Utility OnChip PCI Device OnChip Audio Controller [Enabled] OnChip USB Controller [All Enabled] - USB Device Emulation [None] X - USB Keyboard Support OS X - USB Mouse Support OS - USB 2. 0 Controller [Enabled] Item Help :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults OnChip Audio Controller: This option enables or disables the audio controller. OnChip USB Controller: This option enables or disables the USB controller. USB Device Emulation: This item selects the options of [Keyboard/Mouse], [Keyboard/Mouse/Storage], or [None] devices to be supported in DOS environment. User's Manual 3-18 Chapter 3 USB Keyboard Support: This item allows you to select [BIOS] for using USB keyboard in DOS environment, or [OS] in OS environment. USB Mouse Support: This item allows you to select [BIOS] for using USB mouse in DOS environment, or [OS] in OS environment. USB 2. 0 Controller: This option enables or disables the USB 2. 0 controller. SuperIO Device: Click <Enter> key to enter its submenu: Phoenix ­ AwardBIOS CMOS Setup Utility SuperIO Device POWER ON Function [BUTTON ONLY] KB Power ON Password Enter Hot Key Power ON Ctrl-F1 Onboard FDC Controller [Enabled] Onboard Serial Port 1 [3F8/IRQ4] Onboard Parallel Port [378/IRQ7] Parallel Port Mode [SPP] EPP Mode Select EPP1. 7 ECP Mode Use DMA 3 Game Port Address [210] Midi Port Address [330] Midi Port IRQ [10] Item Help X X X X :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Power On Function: Four options are available: Hot Key Password Mouse Button Only. This iten allow you to choose the computer power turn on method you like. Some item you choose, some of the following items will be available to let you making further setting. For instance, when you set this item to Password, the item of "KB Power On Password" will allow you to enter password. When you set this item to Hot Key, the item of "Hot Key Power On" will allow you to choose the hot key you want. If you choose Mouse, you can press any key on mouse to turn on the computer power. NOTE: To enable this "Power On" function, the wake-up header of [PS2-PWR1], [USB-PWR1], [USB-PWR2] must be set to [Enabled] position. Please refer to the configuration of "Wake-up Header" [PS2-PWR1], [USB-PWR1], and [USB-PWR2] in section 2-4, chapter 2. The mouse wake up function can only be used with the PS/2 mouse, not with the COM port or USB type. Some PS/2 mice cannot wake up the system because of compatible problems. [. . . ] After all, your reseller regards you as an important customer who may purchase more products and who can urge your friends to buy from him or her as well. They should know best what your system configuration is and your problem. If you feel that you need to contact ABIT directly you can send email to the ABIT technical support department. First, please contact the support team for the branch office closest to you. [. . . ]