User manual ABIT IL8

[. . . ] IL8 Intel Pentium 4 System Board Socket 775 User's Manual 4310-0000-40 Rev. 2. 00 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. [. . . ] The remaining "SATA1" and "SATA3" connectors are disabled. [IDE-2]: "IDE1" connector served as [Secondary Master] and [Secondary Slave] channel. "SATA1" and "SATA3" connector served as [Primary Master] and [Primary Slave] channel. The remaining "SATA2" and "SATA4" connectors are disabled. Refer to the following table for the relationships between IDE and SATA ports. PATA IDE Mode Primary Secondary IDE IDE IDE IDE IDE IDE IDE IDE Channel Channel Channel Channel Channel Channel Channel Channel 1 Master 1 Slave 2 Master 2 Slave 3 Master 3 Slave 4 Master 4 Slave IDE1 IDE1 SATA2 SATA4 None None None None Master Slave IDE1 IDE1 SATA1 SATA3 None None None None Master Slave NOTE: This option is configurable only when the item [On-Chip SATA] is set to [Combined Mode]. SATA Mode: This item displays the variety modes for SATA mode. IL8 BIOS Setup 3-13 On-Chip PCI Device: Click <Enter> key to enter its submenu: On-Chip USB Controller: This option enables or disables the USB controller. USB 2. 0 Controller: This option enables or disables the USB 2. 0 controller. USB Keyboard Support: This item allows you to select [BIOS] for using USB keyboard in DOS environment, or [OS] in OS environment. USB Mouse Support: This item allows you to select [BIOS] for using USB mouse in DOS environment, or [OS] in OS environment. On-Chip HD Audio: This option enables or disables the audio controller. Onboard PCI Device: Click <Enter> key to enter its submenu: User's Manual 3-14 Chapter 3 Onboard LAN Controller : This option enables or disables the LAN controller. Invoke Boot Agent: This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. Super IO Device: Click <Enter> key to enter its submenu: OnBoard FDD Controller: This option enables or disables the onboard Floppy Disk controller. Onboard Serial Port: This item determines which I/O addresses the onboard Serial Port controller will access. [Auto]: The system automatically select an I/O address for the onboard Serial Port. [3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3]: Allows you to manually select an I/O address for the onboard Serial Port. [Disabled]: Disables the onboard Serial Port. IL8 BIOS Setup 3-15 3-6. Power Management Setup ACPI Suspend Type: This item selects the type of Suspend mode. Resume by USB From S3: When set to [Enabled], this item allows you to use a USB device to wake up a system that is in the S3 (STR - Suspend To RAM) state. This item can be configured only if the item "ACPI Suspend Type" is set to [S3(STR)]. This item can let you choose when S3 resume active, the VGA BIOS need to be initiative or not. Power Button Function: This item selects the method of powering off your system: [Delay 4 Sec. ]: Pushing the power button for more than 4 seconds will power off the system. This will prevent the system from powering off in case you accidentally hit or pushed the power button. [. . . ] After all, your reseller regards you as an important customer who may purchase more products and who can urge your friends to buy from him or her as well. They should know best what your system configuration is and your problem. If you feel that you need to contact ABIT directly you can send email to the ABIT technical support department. First, please contact the support team for the branch office closest to you. [. . . ]