User manual ABIT AX8-V

[. . . ] (AX8-3rd Eye/AX8/AX8-V) AX8 Series AMD Athlon 64 (FX) System Board Socket 939 User's Manual 4200-0431-01 Rev. 1. 00 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. [. . . ] Full Screen LOGO Show: This item determines to show the full screen logo when booting. User's Manual 3-14 Chapter 3 3-4. Advanced Chipset Features DRAM Configuration: Click <Enter> key to enter its submenu: (Leave these items to their default settings. ) LDT & PCI Bus Control: Click <Enter> key to enter its submenu: (Leave these items to their default settings. ) AX8 Series BIOS Setup 3-15 Back to Advanced Chipset Features Setup Menu: VLink Mode Selection: This item manually selects the VLink Mode. Init Display First: This item selects which slot to initialize first on system boot-up. System BIOS Cacheable: This item decides the system BIOS to be cacheable on system boot-up. CPU Extra Info Show: This item decides to show the CPU operating speed on system boot-up. User's Manual 3-16 Chapter 3 3-5. Integrated Peripherals OnChip IDE Device: Click <Enter> key to enter its submenu: IDE Bus Master: This option enables or disables the IDE bus mastering capability under the DOS environment. The onboard IDE drive interfaces supports IDE prefetching for faster drive accesses. If you install a primary and/or secondary add-in IDE interface, set this field to Disabled if the interface does not support prefetching. Onboard IDE-1/IDE-2 Controller: This item allows you to enable or disable the primary and secondary IDE controller. Select [Disabled] if you want to add a different hard drive controller. AX8 Series BIOS Setup 3-17 Back to Integrated Peripherals Setup Menu: OnChip PCI Device: Click <Enter> key to enter its submenu: OnChip Audio Controller: This option enables or disables the audio controller. OnChip USB Controller: This option enables or disables the USB controller. USB 2. 0 Controller: This option enables or disables the USB 2. 0 controller. USB Emulation: [OFF]: The system does not support any USB device in DOS environment. [KB/MS]: The system supports USB legacy keyboard and mouse; does not support USB storage devices. [ON]: The system supports USB legacy keyboard, mouse, and storage devices. The following options will be available to configure by selecting [KB/MS]. USB Keyboard Support: This item allows you to select [Enabled] for using USB keyboard in DOS environment, or [Disabled] in OS environment. USB Mouse Support: This item allows you to select [Enabled] for using USB Mouse in DOS environment, or [Disabled] in OS environment. User's Manual 3-18 Chapter 3 Back to Integrated Peripherals Setup Menu: Onboard PCI Device: Click <Enter> key to enter its submenu: Onboard LAN Controller: This option enables or disables the LAN controller. LAN Boot ROM: This item enables or disables the Boot ROM on LAN controller. Onboard RAID ROM: This item allows you to use the boot ROM of onboard Serial ATA RAID to boot-up system. Onboard 1394 Controller: This option enables or disables the onboard IEEE 1394 controller. Back to Integrated Peripherals Setup Menu: SuperIO Device: Click <Enter> key to enter its submenu: AX8 Series BIOS Setup 3-19 Onboard FDC Controller: Two options are available: Enabled and Disabled. Onboard Serial Port 1: This is used to specify the I/O address and IRQ of Serial Port 1. [. . . ] After all, your reseller regards you as an important customer who may purchase more products and who can urge your friends to buy from him or her as well. They should know best what your system configuration is and your problem. If you feel that you need to contact ABIT directly you can send email to the ABIT technical support department. First, please contact the support team for the branch office closest to you. [. . . ]