User manual ABIT AN6E

[. . . ] Table of Contents i Pentium Pro Mainboard USER' MANUAL S Table of Contents Chapter 1 System Board Overview Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Component Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 The system block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Chapter 2 Hardware Setup Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Jumper Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Installation of CPU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 Installation of Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 Chapter 3 Award BIOS Setup CPU SOFT MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Standard CMOS Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 BIOS Features Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Chipset Features Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 Power Management Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 PCI & Onboard I/O Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 Load BIOS Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Load Setup Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Setting Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15 IDE HDD Auto Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15 Standard types of hard disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16 Part Number: MN-094-2A1-01 Rev:1. 01 ii Table of Contents Chapter 4 Bus Master IDE Driver System Board Overview 1-1 Chapter 1 System Board Overview The mainboard is designed for the new generation CPU. It supports the Intel CPU SLOT1(Pentium Pro®, Pentium®II . . ), memory up to 1GB, super I/O, and Green PC functions. The mainboard provide high performance for the server system and meet the necessary of the desktop system for Multi-Media in the future. Specifications 1. Memory(DRAM): Supports Intel Pentium Pro® 150~200 MHz, Pentium®II 233~266 MHz Intel 82440 FX chipset Four 72PIN SIMM modules Two 168PIN DIMM modules Supports 8MB to 1GB memory capacity Supports EDO and FP DRAM type Two E-IDE channels Supports up to 4 hard devices Supports two floppy disk drivers up to 2. 88MB One EPP/ECP parallel port (IEEE 1284 Compliant) Two high speed 16550A Compliant UARTs Supports Infrared ­ IrDA(HPSIR) and Amplitude Shift Keyed IR(ASKIR) Supports "PCI Bus master IDE controller" to reduce the work load of the CPU Supports two Universal Serial Bus (USB) interface Supports one PS/2 mouse connector Four 32-bit PCI slots, three 16-bit ISA slots Award Plug and Play BIOS ATX form factor 245 x 305 mm 4. [. . . ] (The Default setting is Disabled. ) Enable this item and the BIOS searches for installed floppy disk drives to determine if they are 40 tracks (360K drive) or 80 tracks (720K, 1. 2M, 1. 44M, or 2. 88M drives). Disable this item and the BIOS does not search for floppy drive type by track number. (The Default setting is Enabled. ) Enable this option to adjust the keystroke repeat rate. Choose how long after you press a key that a character begins repeating. Use this feature to prevent unauthorized system boot-up or use of BIOS Setup. "System" - Each time the system is booted the password prompt appears. "Setup" - If a password is set, the password prompt only appears if you attempt to enter the Setup program. Used to alter VGA palette setting while graphics pass through feature connector of PCI VGA card and processed by MPEG card. BIOS can then execute from RAM. IDE HDD Block Mode Typematic Rate Setting Typematic Rate (Chars/Sec) Typematic Delay (Msec) Security Option PCI/VGA Palette Snoop Video or Adapter BIOS Shadow 3-8 Chapter 3 Chipset Features Setup Menu The Chipset Features Setup Menu are used to change the parameter of the chipset internal registers. Choose "CHIPSET FEATURES SETUP" from the Main Menu and following screen appears. ROM PCI/ISA BIOS (XXXXXXXX) CHIPSET FEATURES SETUP AWARD SOFTWARE, INC. Auto Configuration DRAM Speed Selection DRAM RAS# Precharge Time MA Additional Wait State RAS# to CAS# Delay DRAM Read Burst (B/E/F) DRAM Write Burst (B/E/F) ISA Bus Clock DRAM Refresh Queue DRAM RAS Only Refresh DRAM ECC/PARITY Select Fast Dram Refresh Read-Around-Write Combine PCI Burst Write Combine PCI-To-DRAM Pipeline CPU-To-PCI Write Post CPU-To-PCI IDE Posting System BIOS Cacheable Video RAM Cacheable : Enabled : 60 ns :4 : Enabled : Enabled : x2/2/3 : x3/3/3 : PCICLK/3 : Enabled : Disabled : Disabled : Disabled : Enabled : Enabled : Enabled : Enabled : Enabled : Disabled : Disabled Esc: Quit F1: Help F5: Old Values F6: Load BIOS Defaults F7: Load Setup Defaults : Select Item PU/PD/+/-: Modify (Shift)F2: Color 8 Bit I/O Recovery Time 16 Bit I/O Recovery Time Memory Hole At 15M-16M DRAM Fast Leadoff Passive Release Delayed Transaction :1 :1 : Disabled : Disabled : Enabled : Disabled Figure 3-5 Chipset Feature Setup Menu Note: Memory Hole At 15M-16M Choose Enable or Disable (Default). Used to reserved memory addressing space for some special add-on-card that requires 1M bytes addressing space from 15 to 16M. 2. After you have finished with the Chipset Features Setup, press the <Esc> key and follow the screen instructions to save or disregard your new settings. Award BIOS Setup 3-9 Power Management Setup The Power Management Setup option lets you set the system's power saving functions. Choose "POWER MANAGEMENT SETUP" from the Main Menu. ROM PCI/ISA BIOS (XXXXXXXX) POWER MANAGEMENT SETUP AWARD SOFTWARE, INC. Power Management PM Control by APM Video Off Method Video Off Option Modem Use IRQ Doze Mode Standby Mode Suspend Mode HDD Power Down : User Define : Yes : V/H SYNC + Blank : Susp, stby à off : NA : Disable : Disable : Disable : Disable ** Power Down & Resume Events ** : ON IRQ 3 (COM2) : ON IRQ 4 (COM1) : ON IRQ 5 (LPT2) : ON IRQ 6 (Floppy Disk) : ON IRQ 7 (LPT 1) : OFF IRQ 8 (RTC Alarm) : ON IRQ 9 (IRQ2 Redir) : ON IRQ 10 (Reserved) : ON IRQ 11 (Reserved) : ON IRQ 12 (PS/2 Mouse) IRQ 13 (Coprocessor) :ON IRQ 14 (IDE-1) : ON IRQ 15 (IDE-2) : ON Esc: Quit F1: Help F5: Old Values F6: Load BIOS Defaults F7: Load Setup Defaults : Select Item PU/PD/+/-: Modify (Shift)F2: Color ** Wake Up Events In Doze & Standby ** IRQ 3 (Wake-Up Event) : ON IRQ 4 (Wake-Up Event) : ON IRQ 8 (Wake-Up Event) : OFF IRQ12 (Wake-Up Event) : ON Figure 3-6 Power Management Setup Menu 2. A short description of selected screen items follows: Power Management Options are as follows: User Define Disabled Min Saving Set the power saving options by user. Doze = 1Hour Standby = 1Hour Suspend = 1Hour Doze = 1Min Standby = 1Min Suspend = 1Min Max Saving 3-10 PM Control by APM Video Off Method Chapter 3 Choose No or Yes (Default). If you have a VGA card that is not compatible with the default option, switch to "Blank screen", even though it consumes more power than "V/H SYNC + Blank". If your VGA card and VGA monitor support VESA DPMS, switch the option to "DMPS". Choose "Always On", "All Modes Off" (Suspend, Standby and Doze mode), "Susp, Stby Off"(Default) and "Suspend Off". This item shuts the video off when entering Doze mode, Standby mode or Suspend mode. Setting "Modem Use IRQ" for the APM modem ring wake up function. [. . . ] (Don't select same INT#) ISA: This setting assigns no IRQs to the PCI slots. Use this setting with PCI IDE cards that connect IRQ14 and IRQ15 directly from an ISA slot using a cable from a legacy paddle board. Note: M/B PCI Slot INT# hardware is designed as below: "Slot1-INT#A", "Slot2-INT#B", and "Slot3-INT#C" are assigned to the same IRQ. (Do not use them at the same time. ) "Slot1-INT#B", "Slot2-INT#C", and "Slot3-INT#D" are assigned to the same IRQ. [. . . ]