User manual 3M SOLID SURFACE FINISHING

[. . . ] Application Profile Market: Solid Surface/Cabinet Shop Application Description: Solid Surface Finishing 3MTM TrizactTM Film System Key Application Requirements Random Orbital Sander: 5" 148891 PRODUCTS 3MTM Microfinishing Film 366L (100µ, 60µ) 3M Trizact Disc 268XA (A35, A10, A5) 3M Trizact Disc 568XA (CeO) Products Replaced Competitive coated abrasives, nonwovens, and compounds. Advantages/Benefits for customer ­ Fast, consistent finishing process. ­ Higher gloss level possible ­ crisper reflection, richer appearance. [. . . ] Recommended Sequence for Acrylic-Filled and Polyester-Filled Solid Surfaces Matte Finish 366L 100micron1 dry 268XA A35 damp Scotch-BriteTM A VFN2 Gloss = 12­15 Semi-Gloss Finish 366L 100micron1 dry 268XA A35 damp 268XA A10 damp Scotch-BriteTM S ULF 3 Gloss = 45 High Gloss Finish Standard Sequence Alternate Sequence4 Step 1 Step 2 Step 3 Step 4 Step 5 366L 100micron1 dry 268XA A35 damp 268XA A10 damp 268XA A5 damp acrylic: 568XA CeO damp polyester: Finesse-ItTM Finishing Material Easy Clean-up with 968M 366L 100micron1 dry 268XA A35 damp 268XA A10 damp 268XA A5 damp 286Q 9micron damp Step 6 Gloss = 80 1. Many scratches can be removed with 366L 60micron, which can save time in Step 2. For acrylic, 268XA A10 damp can be used instead of Scotch-Brite A VFN if desired. For acrylic, 268XA A5 damp can be used instead of Scotch-Brite S ULF if desired. Use this method if you encounter swirl marks using the standard sequence or if you desire a very high gloss (over 80). Finesse-ItTM Finishing Material Easy Clean-up Gloss = 80+ NOTE: Rinse debris from Trizact discs after each use, and wipe the surface clean following each step to minimize contamination scratches. Related Applications Acrylic and gel coat repair. Tools Random Orbital Sander Operating Parameters 10, 000 to 12, 000 RPM; 3/16" or 3/32" orbit pattern. 12, 000 RPM and 3/32" orbit pattern tend to provide an improved finish. Accessories 3MTM HookitTM II Disc Pad # 05245 Hookit to Hookit II Conversion Face # 02327 StikitTM to Hookit II Conversion Face # 02331 Market: Solid Surface/Cabinet Shop Application Description: Solid Surface Finishing page 3 Tech Tips 1. It is recommended to use a North-South-East-West abrasive finishing pattern and to employ at least two to four patterns per abrasive step. Each random orbital sander pass should overlap about 25% of the previous pass. To help avoid wild scratches from loose mineral, clean the work surface after each abrasive step using a squeegee and then wiping clean with a paper towel. Rinse debris from the Trizact discs after each use by spraying the discs with water from a plant-misting bottle. For damp sanding, use a plant-misting bottle as a water supply source and add a few drops of dish soap to the water. Emphasize that the damp sanding is damp, not wet, as in Center Water Feed (CWF) applications. Safety Information Always read and follow all safety information included with the product. To request additional product information or to arrange for sales assistance, call 1-800-362-3550. Address correspondence to: 3M Industrial Business Customer Response Center, Building 21-1W-10, 900 Bush Avenue, St. [. . . ] If the 3M product is defective within the warranty period, your exclusive remedy and 3M's and seller's sole obligation will be, at 3M's option, to replace the product or refund the purchase price. Except where prohibited by law, 3M and seller will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental, or consequential, regardless of the legal theory asserted, including warranty, contract, negligence, or strict liability. For Additional Information Product Use Warranty and Limited Remedy Limitation of Liability 3M, Trizact, Scotch-Brite, Finesse-it, Wetordry, Hookit, and Stikit are trademarks of 3M. Industrial Business Building 21-1W-10, 900 Bush Avenue St. [. . . ]