User manual 3M MP8745

[. . . ] Final Copy - 8/26/99 MP8745 Multimedia Projector Operator's Guide MP8745 Projecteur multimédia Guide de l'opérateur MP8745 Multimedia-Projektor Benutzerhandbuch Proyector de Multimedia MP8745 Manual del Usuario MP8745 Proiettore Multimediale Manuale dell'operatore MP8745 Bruksanvisning for multimediaprojektor MP8745 Multimedia Projector Gebruiksaanwijzing R M P E S E T U T T E P IN L A W E R + M P S CU FO U M E N + M O ZO M U T E Y DB AN ST N O P O MP 874 5 PO R TA B LE PR 5 74 P8 M OJ EC TO R EPS-126A Table of Contents Safeguards Warranty Section 1: 1. 1 1. 2 1. 3 1. 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Unpack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Contents of Shipping Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The selected signal input is displayed at the bottom right of the screen. The display will show the last selected input source before power was turned off. 3. 2 Projector Shutdown STANDBY ON 1. After approximately 1 minute, the fan stops and the indicator stays orange. Turn the MAIN POWER SWITCH OI of the projector off. Caution Do not turn off the POWER SWITCH before pressing the STANDBY/ON button. After the STANDBY/ON button is pressed, the fan rotates for about 1 minute to cool the projector. 3. Disconnect cables if moving projector to new location. 3M TM Multimedia Projector MP8745 © 3M 1999 PO RT AB LE PR MP 874 5 OJE CT OR STAN DB Y ON ER W PO + ZO OM EPS-130A ZOOM + Section 4: Adjustments and Functions ENGLISH 0-9 O 4. 1 How To Use Height Adjustment Feet Adjust the image elevation using the height adjustment at the front of the projector. Raise the front end of the projector so the feet are not touching the table top. For fine adjustments, rotate each foot. Caution Do not unlock the foot adjusters if the projector is not supported. If the foot adjusters do not lock completely, turn the foot adjusters slightly before locking. Front View MP8745 Side View 1 RGB IN 2 S-VIDEO IN VIDEO IN OI CONTROL RGB OUT AUDIO IN R MONO R AUDIO IN 2 1 AUDIO OUT USB MD05551 MD05401 Figure 4. 1 Height Adjustment © 3M 1999 3MTM Multimedia Projector MP8745 13 4. 2 Plug & Play Function ENGLISH This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer that is VESA DDC (Display Data Channel) compatible. Plug & play is a system configured with peripheral equipment including a computer and display, and a compatible operating system. Note Use the RGB cable included with this projector when using plug & play. With other cables, pins (12) - (15) are sometimes not connected (effective only for RGB1). 4. 3 Freeze Function The Freeze function is used to display (freeze) a single frame of the image being projected. Note The FREEZE function will turn off during the operation of the MENU, FOCUS, PinP, VOLUME, MUTE, BLANK, MAGNIFY, AUTO or POSITION functions. 4. 4 Magnify Function The Magnify function is used to enlarge a portion of the display image. Press the MAGNIFY (+) button to magnify the center of the displayed image. To move the display area being magnified, press the POSITION button, then use the DISC PAD to move the magnified area up, down, left or right. The MAGNIFY function will turn off during the operation of the MENU, FOCUS, PinP, VOLUME, MUTE, BLANK, FREEZE or AUTO functions. 4. 5 Picture-in-Picture The PinP button on the remote control is used to display a video signal image in the RGB signal image. [small screen size maximum screen size OFF] Both RGB and Video signals must be present for the picture-in-picture function to operate. Press the PinP button on the remote control to display a small PinP screen in the corner of the projector image. Press the PinP button again to enlarge the size of the screen display to maximum. Press the POSITION button on the remote control to change the location of the PinP screen. The position of the picture-in-picture screen can also be changed from the Image menu. [. . . ] Fully insert lamp module or lamp cover and secure with retaining screws. Replace the lamp. Lights red Flashes red Turns off Flashes red Flashes red Turns off *When the LAMP indicator lights or blinks, turn the power off. If the problem persists, contact your dealer. TECHNICAL A-6 3M TM Multimedia Projector MP8745 © 3M 1999 A. 7 Connection to the Control Signal Terminal a) Mouse emulation (1) While the projector and computer are turned OFF, connect the projector and the mouse terminal of computer using an appropriate cable (PS/2, Serial or ADB). See computer's User Manual for this procedure. Note In some Notebook computers with an internal pointing device, mouse emulation will not work unless the internal pointing device is disabled. [. . . ]