User manual 3M 3M-MATIC 800RF BROCHURE

[. . . ] After reading, store this instruction manual in a safe place for future reference. NOTE · The information in this manual is subject to change without notice. TRADEMARK ACKNOWLEDGEMENT : CONTENTS m Page Pr · PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation. · Apple, Mac and ADB are registered trademarks of Apple Computer, Inc. · VESA and SVGA are trademarks of the Video Electronics Standard Association. [. . . ] MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen (or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen. · The MyScreen and the ORIGINAL Screen will each change to the BLANK Screen several minutes after being displayed. Pr Selection of BLANK Screen: MyScreen ORIGINAL . . The BLANK Screen is displayed when the screen has been erased (i. e. , made to vanish) by manipulating the BLANK button (please refer to the "Temporarily Blanking the Screen" section). MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen (or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen. Option screens: Various colored non-patterned (plain) screens displayed within the Menus. · The MyScreen and the ORIGINAL Screen will each change to a non-patterned (plain) black color screen several minutes after being displayed. oje c to r . c : SELECT MENU MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION BLANK START UP MyScreen MyScreen Size MyScreen Lock MyScreen ORIGNAL Example : SCREEN Menu (BLANK) 27 MULTIFUNCTIONAL SETTINGS (continued) OPTION Menu MENU MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION VOLUME AUTO OFF WHISPER LAMP TIME FILTER TIME With the OPTION menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table. OPTION Menu Item VOLUME Adjust Volume: High Description Low AUTO OFF WHISPER LAMP TIME wn loa FILTER TIME 28 de d Refer to LAMP TIME: When set, this function displays the total time the projector lamp has been used since new. Reset LAMP TIME [Use this function only when the lamp has been replaced!]: Depress the RESET button for at least 3 seconds while lamp time is being displayed. After you replace the lamp with a new lamp, select RESET on the menu with the button. You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally). · This function is not available while the lamp is warming up (the power indicator flashes green), while adjusting the volume and display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu screen. oje Press ENTER button Press RESET button Press PAGE UP button Press PAGE DOWN button 1. Turn off the projector and PC power, and connect the projector's control terminal to the computer via the mouse cable. If a USB cable is connected, the USB control function is given priority, and mouse control from the control terminal will not function. If you have difficulty with control, restart the computer (either from the software or by pressing the restart button). Remote Control Operation buttons c to r . c 29 THE LAMP HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately: 78-6969-9599-8), then contact your local dealer. WARNING wait at least 45 minutes, in order to ensure that the lamp is properly cooled. Removing the lamp bulb while it is still hot could cause burns, or cause the lamp bulb to burst. Before replacing the lamp, turn off the power, and unplug the power cord, then wn loa 30 de d The LCD projector uses a glass lamp bulb. High-pressure mercury lamps can break with a loud bang, or burn out, if jolted or scratched, or through wear over time. Each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector's vent holes. · Handle with care: jolting or scratching could cause the lamp bulb to burst during use. · If the replace lamp indicator (see "Related Messages" ( ) and "Regarding the indicator Lamps" ( )) comes on, replace the lamp as soon as possible. [. . . ] 78-6969-9695-4 Adjustable Height Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-6969-9698-8 Shipping Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-6969-9716-8 S-Video Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-3238-1 Mouse Cable (PS/2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]