User manual 3M 3M-MATIC 800A-T SIDE BELT ADJUSTABLE CASE SEALER

[. . . ] For productivity, flaps are folded and tightly sealed at up 28 cases/minute. Easy-to-install and use, you'll be quickly making tight, consistent seals on a wide range of RSCs with minimal operator training. [. . . ] Height and width adjust easily for cases as small as 4. 75" high x 4. 75" wide and as large as 24. 5" high x 21. 5" wide. Sturdy construction and twin motor side drives handle case weights from 5-85 lbs. 3M TM AccuGlideTM Stainless Steel Taping Head · Designed for high moisture and corrosive environments but not for direct high pressure wash down · Upper and lower heads easily removed for service Optional casters · Caster brake and locking swivel for on the job stability · Large 4" diameter polyolefin tires for easy movement · Corrosion-resistant bushing Frame mounted tape drum · Easily mounts up to 16" tape diameter · Use with a full range of Scotch® Box Sealing Tapes in 36 mm to 48 mm widths · Friction drum brake to maintain proper tape tension and prevent overcoasting for smooth tape application Dual masts and dual crossbar · Provides greater stability of taping head position Belt drive assembly and gearmotor on each side · Traction-grip surface on belts for positive case drive through top flap folding and taping · Laced belt construction for replacement ease · Easily replaced assembly · Dual gearmotors to maintain reliable 78'/minute belt speed Top flap compression rollers on each side · Positions and closes flaps before taping for an improved seal 5 Flap folding rods · Precisely closes major box flaps Flap kicker for automatic rear flap closure · Sturdy one-piece construction · Easy-to-use graduated scale for kicker adjustment Convenient on/off switch · Can be repositioned on either side for better access and line changes Hinged access doors · Punched steel to observe case flow · Electrical/pneumatic interlock for safety · Standard left-side mounted; optional right or both side mounted Centrally-located emergency stop on both sides · Easily accessible e-stop · Cuts off electrical and pneumatic 1 Adjustable leg height · Graduated for precise adjustment from 24" to 35" bed height (without casters) Box gate (indexer) · Separates boxes from flooded infeed conveyor · Adjustable pressure and height Air filter/regulator/gauge · Lock-out on/off air valve to maintain proper pressure Width adjustment crank · Set for case widths from 4. 75" to 21. 5" Instructional and safety labeling · Permanently bonded to resist distortion from heat and humidity Box Capacities Length: 6" to 30" Width: 4. 75" to 21. 5" Height: 4. 75" to 24. 5" 6 3M-MaticTM Automatic Adjustable Stainless Steel Case Sealer 800af-s Specifications: Box: Boxes must meet current FBA/PMMI voluntary standards for RSC containers. Boxes not meeting these standards ­ for example, width is more than 50% of length or depth is less than 25% of length ­ should be test run to ensure satisfactory machine performance. Size: Min Max Length 6" (150 mm) 30" (760 mm) Width 4. 75" (120 mm*) 21. 5" (545 mm) Height 4. 75" (120 mm) 24. 5" (620 mm) Special modifications may be available for carton sizes not listed above. Note: The 3M-MaticTM 800af-s can accommodate most boxes within the size range listed above. However, if Box length in Direction of Seal is less than . 6 Box Height boxes should be test run to ensure proper machine performance. 3) All other parts will be free from all defects for two (2) years after delivery. Please refer to individual data pages for additional details and exceptions. If any 3M-warrantied part is proved to be defective within its warranty period, then the exclusive remedy and 3M's and seller's sole obligation shall be, at 3M's option, to repair or replace the part, provided the defective part is returned immediately to 3M's factory or an authorized service station designated by 3M. A part will be presumed to have become defective after its warranty period unless the part is received or 3M is notified of the problem no later than five (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable time, then 3M, at its option, will replace the equipment or refund the purchase price. 3M shall have no obligation to provide or pay for the labor required to install the repaired or replacement part. 3M shall have no obligation to repair or replace (1) those parts failing due to operator misuse, carelessness, or due to any accidental cause other than equipment failure, or (2) parts failing due to non-lubrication, inadequate cleaning, improper operating environment, improper utilities or operator error. [. . . ] 3M shall have no obligation to repair or replace (1) those parts failing due to operator misuse, carelessness, or due to any accidental cause other than equipment failure, or (2) parts failing due to non-lubrication, inadequate cleaning, improper operating environment, improper utilities or operator error. Limitation of Liability: 3M and seller shall not be liable for direct, indirect, special, incidental or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory. [. . . ]